This cell is a solution of inconvenience in using coin and beaker cell for battery research. It is possible to take out from your globe box after assembling the cell. For using a spring inside of the cell, the cell condition is always the same. In addition, disassembling of the cell is easy after performing cycle test, for checking the conditions of electrodes.
This cell is a modified version of the HS Test Cell. By using an internal reference electrode, it is possible to measure cathode and anode electrical potention separately. Thus the cathode and anode data becomes more reliable.
This is a crimping tool for coin cells. Assures almost 100% perfectly sealing for highly accurate mold and control of assembling the tool.
Size : 150 (W) x 350 (L) x 200 (H) mm
(While handle is held up; 340 (H) mm)
Weight : About 12kg
This is an automatic crimping machine for coin cells.
Maintaining the same accuracy as our hand-operated crimping tool, it is so small and safe for a glove-box use.
This tool is used for making disk-shaped electrode for electrochemical research by HS test cell and coin cell. Any disk size is available upon request.
Size : 160 (W) x 240 (L) x 320 (H) mm
Weight : About 5.5kg
This tool is used for making disk-shaped or donut-shaped lithium metal for anode electrode use. Any disk size is available upon request.
Size : 125 (W) x 150 (L) x 195 (H) mm
Weight : About 3.5kg
This machine is used for mixing up battery active material, binder and solution uniformly to make a paste. Although the standard machine is from 150cc to 220L, customization is available. Please contact us for more details and options.
This equipment is used for making electrodes of Li-Ion batteries. It coats He active material paste onto Cu or Al foil uniformly. Although the equipment is compact designed, it has high coating tolerance and winding tolerance.
This equipment is used for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries, after coating and drying, by passing through pre-set gap of rolls. There are 1ton, 2ton and 20ton types for research purposes.
This equipment is used for making a groove at 2 to 8mm from battery case top as preparation of sealing cylindrical cells.
This equipment is used for filling electrolyte in cylindrical and/or prismatic cell by evacuating air out of the cell. It is possible to set filling conditions, such as evacuation level, evacuation holding time, filling speed, pressuring level and time.
This equipment is used for sealing for cylindrical cell with 3 ton press machine. Lower mould, which is set in the press machine, is made of two piece so that operators are easy to set and take out work.
This equipment is used to apply paint, adhesives and active material past to paper or metal foils, using a film applicator such as baker applicator, doctor blade and bar coater. This eliminates irregularities in application and differences among operators.
(Left) Baker type Applicator : Because the blade itself is eccentric, matching the right and left graduations with the guide line marked, the desired film thickness will be available. (0 - 10mil)
(Right) Doctor Blade : This is a metal block which has certain clearance. Sliding on paper or metallic foil, it will produce uniform film as think as the clearance.
(Left) Wire Bar Coater : Stainless wire is winded onto 1/4 inch diameter stainless bar. Difference of wire diameter will produce different thickness of film.
(Right) Micrometer Adjustable Film Applicator : This is a kind of doctor blade but it can change coating thickness. (0 - 10mm)
This equipment is used for slitting electrodes for Li-ion or EDLC, uniformly coated with active materials on metal foils. It is compatible with either electrode-strips or electrodes in reels.
This equipment is used for winding pre-cut length of anode and cathode with separator to make jellyrolls, and winding them flat for prismatic and polymer cells. After setting the electrodes, the winding process is automatic. Winding condition, such as tension and speed, is controllable.
This equipment is used for testing heat sealing conditions of film case of polymer batteries by controlling temperature, pressure and time. The temperature is settable from 50 to 300 degree centigrade, from 0.3 to 3 kg/cm2 as of pressure and from 0.1 to 99.9 seconds as of time.
This equipment is used for filling and sealing polymer batteries under vacuum condition.
Power Source: AC100V three-phase 50/60Hz, 5A
This equipment is used for drawing aluminum laminated films which are cases of polymer batteries. Since pressing speed and force are controllable, it will optimize forming conditions of various types of films. In addition, various size of case can be produced by changing mold.
This is a lamination film which is used for casing of Li-Ion battery and polymer battery. Sheet, three-side sealed and drawn cap are available.
* Nail Stabbing * Compression Break * Over-charge / Over-discharge * Hot-plate
* Out Side Short Circuit * Oven Correspondence